ActronAir Not Heating, Why Your Ducted System Runs Cold
An ActronAir not heating on a cold winter morning can leave the whole house chilly.
Reverse cycle ducted systems behave a little differently in heating mode, so some things that look like faults, such as pauses for defrost, are normal. Others really do need a technician. This guide helps you tell the difference and work through the likely causes.
How does ducted heating work?
In heating mode, an ActronAir reverse cycle system pulls heat from the outside air, even on cold days, and moves it indoors. The outdoor coil becomes cold, while the indoor coil in the roof becomes warm. The indoor fan then pushes air across that warm coil and through the ducts to each open zone.
Because the system moves heat rather than creating it from scratch, it is efficient, often far more so than plain electric heaters. However, it depends on the outdoor coil staying clear of ice and on good airflow indoors. Problems with either reduce heating.
Is the system really in heating mode?
Start with the controller. Check that the mode is heating, not cooling, fan only or automatic with a set point below the room temperature. Make sure the set point sits above the current room temperature and that the zones you want are on.
Also check timers and schedules. A schedule left over from summer may switch the system to cooling or off at certain times. Our modes explained guide explains each setting.
Why does the fan wait before blowing warm air?
When heating starts, the indoor fan often waits until the indoor coil has warmed up. That stops the system from blowing cold air into the rooms. The wait usually lasts a few minutes, though it can feel longer on very cold mornings.
This pause is normal. If the fan never starts or the air stays cold after fifteen minutes or more, something else may be wrong.
What is defrost and why does heating stop?
On cold, damp mornings, frost forms on the outdoor coil. Frost blocks airflow and cuts heating output, so the system runs a defrost cycle every so often. It briefly reverses to send heat to the outdoor coil and melt the frost. During defrost, the indoor fan slows or stops so cold air does not blow inside.
You may see steam rising from the outdoor unit and water running from its base. On ESP Platinum systems with the QUE controller, you may see status messages such as deF during defrost and a countdown before it starts. Defrost usually lasts a few minutes, then heating resumes. This is normal behaviour for every reverse cycle system.
When is defrost a problem?
Defrost becomes a problem when it happens very often, lasts a long time or fails to clear the ice. Signs include heavy ice covering the whole outdoor coil, ice building up from the base and a house that never gets warm.
Possible causes include a faulty outdoor coil sensor, shown as E07, blocked drain holes, low refrigerant or a reversing valve problem. ESP Platinum systems also list a code for defrost timing out. Book a technician if ice keeps building.
Is the return air filter blocked?
A clogged filter affects heating as well as cooling. In heating mode, poor airflow lets heat build up in the indoor coil, pressure rises and the system may cut out or show a high pressure code such as E11. Rooms stay cool even though the air near the unit feels hot.
Clean the filter behind the return air grille if it looks dusty. Our filter cleaning guide explains how.
Are too many zones closed?
Closing most zones restricts airflow in heating just as it does in cooling. The indoor coil overheats, and the system may slow down or stop to protect itself. Open at least two or three zones and see whether heating improves. If it does, ask a technician to review the minimum zone setting so the system always keeps enough airflow.
Is the outdoor unit running?
Go outside and check whether the outdoor unit runs while the system is in heating mode. Apart from defrost pauses, the fan should spin and the compressor should hum. If the outdoor unit stays silent, the system cannot heat.
Check the switchboard for tripped breakers and look for codes on the controller. Our outdoor unit not running guide covers the next steps.
Could the system be low on refrigerant?
Low refrigerant reduces heating just as it reduces cooling. Owners often notice weaker performance gradually, then a system that barely heats on cold mornings. Since refrigerant is not consumed, a low charge always means a leak.
A technician finds and repairs the leak, then recharges the system to the correct weight. Our gas and regas page explains the process.
Could the reversing valve be stuck?
The reversing valve switches the system between heating and cooling. If it sticks, the system may blow cool air in heating mode or struggle to defrost. A stuck valve can come from wear, debris or an electrical fault in its coil.
A technician can test the valve and its coil. Sometimes a gentle electrical test frees it, while other times it needs replacing. Replacement involves recovering the refrigerant and brazing in a new valve, so it is a bigger job that the technician will explain fully before starting.
Do blocked drain holes cause heating problems?
Yes. During defrost, melted ice drains through holes in the base of the outdoor unit. If leaves, soil or debris block those holes, water pools in the base and refreezes. Ice then builds up from the bottom, eventually reaching the coil and the fan.
Clearing the area around the base helps. Look for leaves packed against the unit and make sure water can flow away. If ice has already built up inside the base, leave it for a technician, who can clear the holes safely once the unit is off.
Could the outdoor fan be failing?
In heating mode, the outdoor fan pulls air across the cold outdoor coil so it can collect heat. A slow or failed fan means less heat collected and faster icing. You may notice the fan wobbling, scraping or not spinning while the compressor runs.
A failing outdoor fan needs a technician. Running the system without proper fan operation can lead to heavy ice and pressure faults.
Is supplementary heating worth considering?
Reverse cycle ducted systems are efficient, but on the very coldest mornings some homes benefit from a little extra help. A portable electric heater in one room or a heated throw can take the edge off while the ducted system brings the rest of the house up to temperature.
That said, if your system has always struggled, a capacity or insulation issue may be the real story. A technician can help you decide whether the system needs repair, adjustment or simply better support from the building.
What codes can appear when heating fails?
Codes related to heating problems include E07 for the outdoor coil sensor, E11 for high pressure, E09 for low pressure and E22 for the outdoor ambient sensor. Communication codes can also stop heating altogether.
Record any code and check our error code guide for details.
Does the outside temperature affect heating?
Reverse cycle systems become less effective as outdoor temperatures drop, because there is less heat in the air to collect. On the coldest Sydney mornings, especially in western suburbs, the system may need longer to warm the house.
Starting the system earlier with a timer helps. So does keeping doors closed and heating only the rooms you use. Our timer settings guide explains schedules.
Is the house losing heat too quickly?
Poor insulation, draughty windows and doors and open plan spaces with high ceilings all lose heat quickly. The system may run constantly yet never reach the set point.
Simple steps help, such as closing curtains at dusk, sealing draughts with door snakes or weather strips and closing doors to unused rooms. If the house has always been hard to heat, ask a technician whether the system capacity suits the home.
What safe checks can you do now?
Work through these steps.
- Confirm heating mode, a set point above room temperature and the right zones.
- Check timers and schedules.
- Wait at least ten minutes after start up for the coil to warm and the fan to start.
- Clean the return air filter if it is dusty.
- Open at least two or three zones.
- Check that the outdoor unit runs, allowing for defrost pauses.
- Clear leaves and debris from around the outdoor unit and its base.
- Check the switchboard and try one full power reset.
If heating does not improve after half an hour, book a technician.
When should you switch off and call straight away?
Turn the system off at the switchboard if you see heavy ice that does not clear, water dripping inside, smoke or a burning smell, or if you hear grinding or banging. Never pour hot water on an iced outdoor unit or chip at the ice.
Why does heating feel uneven between rooms?
Uneven heating usually comes from airflow differences between zones. Rooms at the end of long duct runs, rooms with large windows and rooms on the cold side of the house often feel cooler. Warm air also rises, so upstairs rooms may feel warmer than downstairs ones.
Balancing outlets, adjusting zone settings or adding zone sensors can improve evenness. A technician can check the duct layout and suggest changes that suit your home.
How does a technician diagnose heating problems?
The technician checks settings, the filter, zones and airflow first. Then they watch the system through a heating cycle, including defrost if conditions allow. They measure temperatures and pressures, test the outdoor coil sensor and the reversing valve and look for leaks.
They also check the outdoor unit for blocked drain holes and damage. Once they find the cause, they explain the repair and cost before starting.
How can you stay warm while waiting for a repair?
Close curtains and blinds as the sun goes down to hold warmth inside. Shut doors to unused rooms and gather in one space. A safe portable heater, used according to its instructions and kept clear of curtains and bedding, can warm a single room.
Warm clothing and blankets help too. If anyone in your home is elderly, very young or unwell, let us know when you book so we can take that into account when arranging the visit.
Can servicing prevent winter heating problems?
An autumn service is a great way to prepare for winter. The technician cleans the coils, checks the fans, confirms the refrigerant charge, tests defrost components and clears the outdoor unit base. Those checks catch many heating problems before the first cold snap.
Our ActronAir service page explains what a ducted service includes.
How do you book help with an ActronAir not heating in Sydney?
When your ActronAir is still not heating after these checks, phone 02 9071 1142 or use the form on our contact page. Let us know whether the air is cold or just weak, whether you see ice outside and any codes on the controller.
Please make the roof manhole, the return air grille and the outdoor unit easy to reach so the technician can begin testing without delay.
Frequently asked questions
Why does my ActronAir blow no air for a few minutes in heating?
The fan waits for the indoor coil to warm up so it does not blow cold air. This pause is normal.
Why does my ActronAir stop heating on cold mornings?
It is probably defrosting the outdoor coil. Heating resumes after a few minutes. Frequent or long defrosts may need a check.
Is ice on the outdoor unit normal in winter?
Light frost that clears during defrost is normal. Heavy ice that keeps building needs a technician.
Can a dirty filter stop my ActronAir heating?
Yes. Poor airflow lets heat build up in the indoor coil, which can trip the system and leave rooms cold.
Why is my ActronAir blowing cold air in heating mode?
Possible causes include the wrong mode, a defrost cycle, a stuck reversing valve, low refrigerant or an outdoor unit that is not running.
When is the best time to service for winter?
Autumn is ideal, so the system is clean and checked before the first cold snap.