ActronAir E28 Error, Inverter Drive Temperature High
Inverter drives turn a lot of electrical power into compressor motion, and they create heat while they do it. The ActronAir E28 error tells you the drive has crossed its safe temperature and stopped. This page explains how the drive keeps cool, what usually stops that cooling and what a repair involves.
What does the ActronAir E28 error mean?
The inverter drive sits inside the outdoor unit and contains power components that switch electricity at very high speed. Those components warm up as they work. A heat sink, often with fins, draws the heat away, and the outdoor fan blows air across it.
ActronAir lists E28 as drive temperature high on its Advance and Aires ducted systems, and the ESP Platinum table for QUE controllers uses the same description. When the drive temperature sensor reports a reading above the limit, the drive stops the compressor and sends the code to the controller.
How does the drive stay cool?
Most ActronAir outdoor units cool the drive in one of two ways. Some mount the power components on an aluminium heat sink that sits in the path of the outdoor fan. Others use refrigerant cooling, where a cold refrigerant line passes behind the heat sink plate. Some designs combine both.
Either way, the drive depends on the rest of the system working properly. If airflow drops or refrigerant flow changes, the heat sink cannot shed heat fast enough, and drive temperature climbs.
What causes an E28 fault?
Several conditions can push drive temperature too high. Common causes include the following.
- Dust, leaves or insects blocking the heat sink fins.
- An outdoor fan that runs slowly or not at all.
- Very hot weather combined with direct sun on the outdoor unit.
- An outdoor unit in an enclosed space that recirculates hot air.
- Heavy compressor load from a dirty coil or high pressure.
- Dried out thermal paste between the power module and heat sink.
- A failing drive temperature sensor.
- Low refrigerant on drives that rely on refrigerant cooling.
Airflow and heat related causes make up most E28 calls in Sydney. Component failures inside the drive are less common but do occur on older systems.
Why does E28 often appear in summer?
Summer adds heat from every direction. The air around the outdoor unit is hotter, so the heat sink has less temperature difference to work with. At the same time, the compressor works harder to cool your home, which means the drive handles more power and creates more heat.
On a hot afternoon, a drive that copes perfectly in spring can tip over its limit. Units in full western sun or enclosed courtyards feel this most. That is why the first E28 calls of the year often arrive in the first heatwave, sometimes on the very same afternoon across many suburbs.
What signs come with E28?
The system usually stops during heavy use, often in the late afternoon. The outdoor unit goes quiet, and the controller shows the code. After it cools down, the system may restart and run for a while before tripping again.
Before the trip, some systems reduce compressor speed to keep the drive cooler. ActronAir lists a separate code for derating due to high drive temperature on ESP Platinum systems. If you noticed weaker cooling before E28 appeared, that derating may explain it.
What does derating mean?
Derating means the system deliberately reduces its own output to stay within safe limits. When drive temperature rises, the board lowers compressor speed. Less power through the drive means less heat, which may keep it below the trip point.
Owners notice derating as weaker cooling on the hottest days. If derating cannot hold temperature down, the drive eventually stops with E28. So, regular weak cooling on hot afternoons can be an early warning.
What safe checks can owners do?
Most of the drive is inside the outdoor unit, so owner checks focus on the surroundings.
- Turn the system off at the wall controller.
- Clear leaves, plants and stored items from around the outdoor unit.
- Make sure nothing blocks the fan outlet or the air intake side.
- Check whether the unit sits in full sun or a hot enclosed spot.
- Wait at least half an hour for the drive to cool before one restart.
If E28 returns, leave the system off and book a visit. Our outdoor unit checks guide explains what you can safely look at.
What does a drive temperature sensor measure?
The drive usually carries its own temperature sensor, mounted on or near the power module or heat sink. Some designs build the sensor into the power module itself. The board reads it constantly and compares the value with limits set by ActronAir.
If the sensor fails, it may report a temperature that is too high even when the drive is cool. That causes false E28 trips. On the other hand, a sensor that reads too low could let the drive overheat without warning, though other protections usually step in. For both reasons, technicians test the sensor rather than assume the drive is genuinely hot.
Why does thermal paste matter?
Between the power module and the heat sink sits a thin layer of thermal paste or a thermal pad. It fills microscopic gaps and lets heat flow into the metal. Over many years of heating and cooling, paste can dry out, crack or migrate, leaving air gaps.
Air conducts heat poorly, so a dried layer lets the module run hotter even when the heat sink stays clean. Renewing the paste is a delicate job because the module must be removed and refitted with the right torque. When done properly, it can bring drive temperatures back to normal.
Can pests cause E28?
They can. Rodents and insects like the warmth around outdoor electronics. Nests can block heat sink fins, and droppings can trap dust and moisture. In some cases, pests also damage cables, which leads to other faults alongside E28.
If you have seen pests around the outdoor unit, mention it when you book. The technician can clean out the cabinet and suggest ways to discourage pests from returning.
Should you spray water on the outdoor unit to cool it?
No. Water can reach electrical parts, especially on a unit with damaged seals or open gaps. It can also bend coil fins or wash dirt deeper into them. On a hot day, a sudden spray may cool the cabinet briefly but does not fix the cause.
Shade that does not block airflow can help in the long run. However, the best fix is to find and correct whatever stops the drive from cooling.
How does a technician diagnose E28?
The technician starts with the outdoor fan and the space around the unit. Then they isolate power, let the capacitors discharge and open the unit to inspect the heat sink. Blocked fins, nesting material and dust build up are common findings.
Next, they check the drive temperature sensor and compare its reading with the actual heat sink temperature. They also measure refrigerant pressures and compressor current to see whether the drive is carrying a heavy load. On refrigerant cooled designs, they check that the cooling line is working as intended.
What repairs fix E28?
The fix depends on the cause found during testing. Typical repairs include the following.
- Cleaning the heat sink fins and the outdoor coil.
- Repairing or replacing the outdoor fan motor or its driver.
- Removing nests and sealing pest entry points.
- Renewing thermal paste between the power module and heat sink.
- Replacing a faulty drive temperature sensor.
- Correcting the refrigerant charge on refrigerant cooled designs.
- Replacing the drive board if its components have degraded.
After the repair, the technician runs the system under load and confirms that drive temperature stays within normal limits.
How long does an E28 repair take?
Cleaning and fan repairs usually finish on the first visit. Thermal paste renewal and sensor replacement also tend to be quick if parts are on hand.
Drive board replacements take longer because they depend on ordering the correct ActronAir part. The technician will explain the timing before leaving and make sure the system is safe in the meantime.
Can E28 damage the drive permanently?
The trip is there to prevent permanent damage. However, a drive that has run near its limit for a long time may have aged faster. Power components that repeatedly reach high temperatures wear out sooner.
That is why fixing the cause quickly matters. A clean heat sink and a working fan keep the drive running cool, which extends its life considerably and protects your investment in the system.
Does the location of the outdoor unit matter?
Location has a big effect on drive temperature. Units on west facing walls, on dark roofs or in narrow passages between buildings run hotter than units in open shade. Units under decks or behind solid screens can trap their own exhaust heat.
If E28 appears every summer, ask the technician whether shading or relocation would help. Any shade structure must leave plenty of space around the unit so air can move freely.
What should you tell us when booking?
Helpful details include the time the code appeared, the outdoor temperature, whether the outdoor unit sits in sun and whether cooling felt weaker before the trip. Also mention any pest activity, recent storms or building work near the unit.
With that information, the technician can bring cleaning gear, a replacement sensor or fan parts as needed. As a result, there is a better chance of fixing the fault in a single visit.
Which codes relate to E28?
Other drive codes include overcurrent, shown as E26, and drive trip lock, shown as E30. Low supply voltage shows as E29, and low DC link voltage shows as E41.
High discharge temperature, shown as E06, often appears in the same conditions, since both relate to heat and heavy load. Our ActronAir error code list groups these codes.
Can servicing prevent E28?
A service cleans the outdoor coil, checks the fan and looks inside the outdoor unit for dust and debris around the electronics. Those checks keep the heat sink clear and the fan working, which is exactly what the drive needs.
Booking a service before summer gives the system the best chance of coping with the first heatwave. Our ActronAir service page explains what a full ducted service includes.
Is an E28 repair expensive?
Many E28 repairs are affordable, especially cleaning, fan repairs and sensor replacements. Drive board replacements cost more, and access difficulties add time and expense.
We do not quote a fixed price before seeing the system. Instead, the technician diagnoses the cause and gives you the cost before starting work. Our pricing page explains the main factors that affect cost.
How do you book an ActronAir E28 error repair in Sydney?
To book help with an ActronAir E28 error, call 02 9071 1142 or use the form on our contact page. Tell us the code, the controller model, your suburb and whether the fault appears on hot afternoons.
Before the visit, clear access to the outdoor unit and unlock side gates. If the unit is on a roof or high bracket, let us know so the technician can plan safe access.
Frequently asked questions
What does ActronAir E28 mean?
ActronAir lists E28 as drive temperature high. The inverter drive in the outdoor unit got hotter than its safe limit and stopped the compressor.
Why does my ActronAir show E28 on hot days?
Hot air reduces cooling for the drive, and the compressor works harder at the same time. A dirty heat sink or weak fan makes it worse.
Can I cool the outdoor unit with a hose to clear E28?
No. Water can reach electrical parts and damage the coil. Turn the system off, let it cool and book a technician.
What is derating on an ActronAir system?
Derating means the system reduces compressor output to keep the drive cooler. You may notice weaker cooling before E28 appears.
Will shade help prevent E28?
Shade can help if it leaves plenty of airflow around the outdoor unit. A technician can advise on safe options.
Does E28 mean the drive needs replacing?
Not usually. Cleaning, fan repairs or a sensor replacement often fix E28. A drive replacement is only needed if testing shows it has failed.