ActronAir Gas Regas Sydney, Leak Finding Before Refilling
ActronAir gas regas Sydney requests usually start with a system that blows weak or warm air.
However, refrigerant does not get used up like fuel, so a low charge almost always means a leak somewhere. This page explains how we find that leak, repair it and then recharge your ActronAir system to the correct amount.
Why does an ActronAir system lose gas?
Refrigerant travels in a sealed loop between the indoor and outdoor units. In theory, it should last the life of the system. In practice, small leaks can develop over the years, so the charge slowly drops until the system struggles.
Common leak points include flare joints at the indoor or outdoor unit, brazed joints, service valves, pipe runs that rub against framing and coils that corrode over time. Coastal homes see more coil corrosion because salt air attacks thin metal fins and tubes. Likewise, pipes that vibrate against a wall or roof timber can wear through slowly.
What are the signs of low refrigerant?
Low refrigerant often shows up gradually. Typical signs include the following.
- Cooling that feels weaker than it used to, especially on hot afternoons.
- Heating that takes much longer to warm the house.
- Ice on the indoor coil or on the thin pipe at the outdoor unit.
- A hissing or bubbling sound near the pipes.
- Longer run times and higher power bills.
- Fault codes linked to low pressure or high discharge temperature on some models.
On ActronAir systems, a low charge can contribute to codes such as E09 or E10, depending on the range. Even so, a code alone does not prove a leak, so testing comes first.
Why not just top up the gas?
Topping up without finding the leak only delays the problem. The new gas escapes the same way the old gas did, so the system goes low again within weeks or months. Meanwhile, running a system low on refrigerant stresses the compressor, which is the most expensive part to replace.
For this reason, we treat a regas as a repair job. In other words, we find the leak, fix it, prove the repair holds and only then recharge the system.
How do we find refrigerant leaks?
Leak finding uses several methods, and the right mix depends on the system and where the pipes run.
- First, a visual check of joints, valves and coils for oil stains, which often mark a leak.
- Next, an electronic leak detector passed slowly along joints and pipe runs.
- Then bubble solution on suspect joints, which foams where gas escapes.
- If the leak stays hidden, a nitrogen pressure test that holds the system at pressure for a set time.
Nitrogen testing is especially useful on ducted systems because long pipe runs pass through walls and roofs. If the pressure falls, the technician knows a leak exists and can split the system into sections to narrow it down.
Where do ActronAir leaks usually appear?
In our experience, flare joints at the indoor unit and outdoor unit service valves account for many leaks. Ducted indoor coils can also leak where copper tubes pass through the end plates, since vibration and moisture slowly wear those points. Outdoor coils near the coast tend to pit and pinhole after many years.
Older Classic systems may have joints that have loosened through years of heating and cooling cycles. Newer inverter systems such as Advance and Aires are not immune either, especially when the original install used poor flares or long pipe runs without proper support.
How is the leak repaired?
The repair depends on what failed. A leaking flare can usually be cut back and remade with a fresh flare. For a leaking brazed joint, the technician cleans and rebrazes it under a nitrogen purge, which stops scale forming inside the pipe. If a coil leaks, the technician may be able to repair a single accessible point, although a badly corroded coil usually needs replacing.
After the repair, the technician pressure tests again with nitrogen. Once the pressure holds, they move on to the vacuum stage.
Can a dirty coil look like low gas?
Yes, and that is one reason we test before charging. A heavily blocked indoor filter or coil cuts airflow, which drops coil pressure and can make gauges look like the system is short. Likewise, a dirty outdoor coil raises head pressure and reduces cooling, which again can feel like a gas problem from inside the house.
So before anyone adds refrigerant, the technician checks filters, coils and fan speeds. If cleaning solves the problem, you avoid paying for gas the system never needed. Our filter cleaning guide shows how to keep the return filter clear between visits.
Why does the vacuum stage matter?
Air and moisture inside a refrigerant system cause real damage. Moisture mixes with oil and refrigerant to form acids, while air raises pressures and reduces efficiency. So before any new refrigerant goes in, the technician pulls a deep vacuum with a vacuum pump and checks it with a micron gauge.
If the vacuum holds steady, the system is dry and tight. If it rises, there may still be moisture or a small leak, so the technician keeps working until the reading settles.
How is the correct charge worked out?
Every ActronAir outdoor unit carries a data plate showing the refrigerant type and the factory charge. Longer pipe runs need extra refrigerant, so the installer should have recorded any additional charge at installation. Our technician uses those figures and weighs the refrigerant in with digital scales rather than guessing by pressure alone.
Afterwards, they run the system and check pressures, temperatures and superheat or subcooling to confirm everything sits where it should. That way, the system runs efficiently and the compressor stays protected.
Which refrigerants do ActronAir systems use?
ActronAir systems in Sydney homes use different refrigerants depending on their age. Older systems commonly use R22 or R410A, while newer systems may use R32 or R410A. The data plate on the outdoor unit shows which one your system uses.
Australia is phasing out R22, so supply keeps shrinking and the gas costs more. If an R22 system has a major leak, our technician will explain whether repair still makes sense or whether replacement offers better value over time.
Is a regas dangerous to do yourself?
Yes. Handling refrigerant in Australia requires an appropriate licence, because refrigerants can cause cold burns, displace oxygen in small spaces and harm the environment if released. Some newer refrigerants are mildly flammable as well. DIY regas kits also tend to overcharge or contaminate systems.
Instead, leave refrigerant work to licensed technicians who carry the right tools and recover old refrigerant properly.
How long does a gas regas take?
A straightforward job on a split or small ducted system with an easy to find leak may take a few hours. However, a hidden leak on a long ducted pipe run can take longer, especially if the technician needs to open ceilings or work in a hot roof. If the job needs parts such as a coil, it may take two visits.
When we book the job, we give you a realistic time frame based on your system and symptoms.
What does a regas cost?
The cost depends on how long leak finding takes, what the repair involves, the refrigerant type and how much refrigerant goes in. Because each job differs, we explain the findings and the price before the repair starts, so there are no surprises. Our pricing page explains how we quote.
Can regular servicing prevent leaks?
Servicing cannot stop every leak, but it helps catch problems early. During a service, the technician checks pressures and temperatures, looks for oil stains at joints and checks pipe supports. As a result, a slow leak often gets found before the system runs badly low.
Keeping the outdoor coil clean also helps the system run at normal pressures, which puts less strain on joints over time.
Why does ice form when the gas runs low?
It sounds backwards, but a system short of refrigerant often ices up. When the charge drops, pressure in the indoor coil falls too, and lower pressure means a colder coil. Once the coil drops below freezing, moisture from the room air freezes onto the fins.
As the ice builds, it blocks airflow, so the coil gets even colder and the ice spreads. Eventually, the room gets little or no cool air at all. If you see ice, switch the system to fan only or turn it off and let it thaw, then call us. Our freezing up page explains other causes as well.
What happens if a system gets overcharged?
Too much refrigerant causes its own problems. Pressures rise, the compressor works harder and liquid refrigerant can reach the compressor, where it may damage valves and bearings. Efficiency also drops, so running costs go up rather than down.
Overcharging often happens when someone tops up by feel or by pressure alone on a hot day. That is why our technicians weigh the charge in against the data plate figures and then confirm the result with temperature readings.
Why do some newer systems leak early?
A system that leaks within its first few years usually points to an installation issue rather than worn parts. Poorly made flares, overtightened or undertightened flare nuts, kinked pipes and pipes left without support all raise the risk. Similarly, if the installer skipped a proper nitrogen test or vacuum, small faults may show up only after months of use.
If your system is fairly new and already low on gas, keep your installation paperwork handy. It may help with any warranty discussion, and it also tells our technician about pipe lengths and any extra charge.
Does pipe insulation matter?
Yes, more than many people expect. The thick foam on the pipes stops the cold suction line from sweating and dripping, and it also protects the pipes from sun damage. Once the insulation breaks down, condensation can drip into walls or ceilings, and exposed copper outside can weather over time.
During a regas, the technician checks the visible insulation and tape. Where it has cracked or fallen away, they can replace it so the pipes stay protected.
What does a regas visit look like from start to finish?
Most visits follow the same order. To begin, the technician listens to your description and reads any fault code. Next, they check airflow, filters and coils, since a dirty coil can mimic low gas. Then they connect gauges, compare pressures and temperatures against expected values and decide whether a leak test is needed.
After that comes leak finding, the repair, a pressure test, the vacuum and finally the weighed charge. At the end, they run the system in your normal mode and explain what they found and fixed, so you know what happened inside your system.
Who handles ActronAir gas regas Sydney wide?
We handle ActronAir gas regas Sydney wide, across the Eastern Suburbs, North Shore, Western Sydney and South Sydney. To book, phone 02 9071 1142 or use our contact page. When you call, mention your model, the symptoms and any code on the controller.
Before the visit, clear access to the outdoor unit and the indoor unit or roof manhole. That way, the technician can start testing straight away. Also, if you have any past service reports or invoices that mention refrigerant work, keep them handy, because they help the technician judge how quickly the system has been losing gas.
Frequently asked questions
Does an ActronAir system need regular gas top ups?
No. Refrigerant runs in a sealed loop, so a low charge almost always means a leak that needs repair.
How do you find a refrigerant leak?
We use visual checks, electronic leak detectors, bubble solution and nitrogen pressure testing.
Why do you pull a vacuum before regassing?
A deep vacuum removes air and moisture, which would otherwise damage the system and reduce efficiency.
Can I regas my air conditioner myself?
No. Refrigerant work requires a licence, along with the right tools and safe recovery practices.
Which refrigerant does my ActronAir system use?
Check the data plate on the outdoor unit. Older systems often use R22 or R410A and newer ones may use R32.
How long does a regas take?
Simple jobs may take a few hours, while hidden leaks on long ducted pipe runs can take longer.